MicroSilk™ FAQ's
Can Bath Salts, Teas, Oils, and Aromatherapy Oils be used in a MicroSilk™ Hydrotherapy unit?How often should i clean the pre-filter? How often should i clean the Stainless Steel screen?Do you clean/flush the unit? How often?What is the Voltage Requirement for MicroSilk™?What is the WarrantyHow do you create the oxygen/where does it come from?Does it come in a pedestal?Will it help any skin conditions?Can i use both hydrotherapies in a combo unit simultaneously?Why aren't MicroSilk™ and it's combinations available in all bath models?Does a MicroSilk™ only bath purge itself?Does a MicroSIlk™ only Bath have a Blower?Does a MicroSilk™ only Bath have a heater?Is it a mutli Speed?How do i put my face in it?
SELECTING A JASON PRODUCT
What types of therapy must be considered when selecting a Jason bath? What dimensions must be considered when selecting a Jason bath? How do I select a 2-person bath?What shapes should I consider when selecting Jason baths? What colors are available?
INSTALLING A JASON PRODUCT
What is the electrical supply service needed for a Jason therapy bath? What type of service access is required for my Jason therapy bath? What size water heater is needed for operating my Jason therapy bath?What is a Level-Form™ Base? Does Jason offer installation templates?
CLEANING AND CARE OF YOUR JASON BATH
How should I maintain the acrylic surface of my whirlpool bath? How should I clean the plumbing lines of my whirlpool bath?Can I add oils and bathing salts to my Jason therapy bath?
PURCHASING JASON PRODUCTS
Where can I purchase Jason products? How can I obtain pricing information and purchase Jason products?What is the usual lead time for Jason baths, and can I quick ship a bath?Can I buy Jason products directly?How do I register my bath?Where can I locate the serial number for my bath?
MicroSilk™ FAQ's
Q: Can Bath Salts, Teas, Oils, and Aromatherapy Oils be used in a MicroSilk™ Hydrotherapy unit?
A: Yes, these non-foaming additives may be used in our AirMasseur® and Whirlpool baths as well. You may notice the amount of aromatherapy oils necessary will be reduced in a MicroSilk™ bath. The oils will float to the surface and be aerosolized with Anions rather than being emulsified in the bath water.
back to top 
Q: How often should i clean the pre-filter? How often should i clean the Stainless Steel screen?
A: This will depend on use. The EZ Clean Pre-filter and stainless steel screen should be cleaned before the initial use to remove any debris that was trapped during installation. Then rinse any visible debris out of the pre-filter after each bath. If the performance of the bath diminishes, remove the stainless steel screen and rinse it according to the instructions and operations manual.
back to top
Q: Do you clean/flush the unit? How often?
A: We recommend any hydrotherapy bath (AirMasseur®, Whirlpool, or MicroSilk™) should be flushed and cleansed with Jason cleaner or a non-foaming detergent at least once a month.
back to top
Q: What is the Voltage Requirement for MicroSilk™?
A: 120V for Standard or Premier Equipment
240V for Signature Equipment
back to top
Q: What is the Warranty
A: The warranty for MicroSilk™ are the same for the other Jason forma® and Designer Collection baths, which is seven years on the shell and three years on the mechanical and plumbing systems.
back to top
Q: How do you create the oxygen/where does it come from?
A: Ambient air is drawn into the system through a venturi and dissolved at elevated pressures through our patented process. Although we are increasing the percentage of all ambient gases, only oxygen can be utilized by our skin's cells.
back to top
Q: Does it come in a pedestal?
A: No, not at this time.
back to top
Q: Will it help any skin conditions?
A: We have received testimonials from user's experiencing relief from eczema and psoriasis after using a MicroSilk™ bath.
back to top
Q: Can i use both hydrotherapies in a combo unit simultaneously?
A: Yes. Although, it is recommended that the MicroSilk™ system be used independently to maximize the cleaning cloud of microbubbles, dissolved oxygen and therapeutic levels of Anions.
back to top
Q: Why aren't MicroSilk™ and it's combinations available in all bath models?
A: Each type of hydrotherapy equipment has different space requirements. Some of our baths do not provide enough room under the perimeter of the bath to accept the MicroSilk™ and/or other equipment.
back to top
Q: Does a MicroSilk™ only bath purge itself?
A: Yes. The MicroSilk™ system is designed to drain itself after every use, and does not require an air/power assisted purge.
back to top
Q: Does a MicroSIlk™ only Bath have a Blower?
A: No, MicroSilk™ produces billions of microbubbles by pressurizing a small volume of water and releasing it back into the bathing well at near atmospheric pressure.
back to top
Q: Does a MicroSilk™ only Bath have a heater?
A: No, a MicroSilk™ bath maintains the temperature of the bath water through the heat energy created when the microbubbles implode (collapse) beneath the waters surface.
back to top
Q: Is it a mutli Speed?
A: No. A single speed is all that is required to create microbubbles.
back to top
Q: How do i put my face in it?
A: Use the new Jason MicroSilk™ Wand to spray the skin rejuvenating benefits of the MicroSilk™ on your face.
back to top
SELECTING A JASON PRODUCT
Q: What types of therapy must be considered when selecting a Jason bath?
A: Jason offers the broadest selection of bath therapy options in the market. With Jason, the choice is yours.
Jason Whirlpool baths with their Perfect-Pressure/Perfect-Flow™ fully adjustable whirlpool jets, deliver a deep, invigorating massage focused on specific areas of your body.
Jason AirMasseur® baths offer a more subtle, full-body hydromassage by surrounding you with millions of warm-air bubbles. Numerous, strategically spaced warm-air jets give a sensuous full body massage with variable pulse, wave, or continuous massage action.
Jason Soaking baths are ergonomically designed baths without whirlpool or AirMasseur® therapy jets. They allow you to simply submerge in warm water and rest in an optimally relaxed position.
Jason Air-Whirlpool baths include Soaking, AirMasseur®, and Whirlpool hydrotherapies into one vessel. It is a customizable bathing experience that allows you to select the hydrotherapy that addresses your individual need or combine all three hydrotherapies for optimum relaxation and therapeutic benefit.
Jason MicroSilk™ baths is a product created with oxygen-rich microbubbles and is an innovative new form of hydrotherapy, that yields unique health and beauty benefits.
back to top
Q: What dimensions must be considered when selecting a Jason bath?
A: The most critical dimension in bath selection generally is the length of the bath, especially in an alcove installation. Standard Jason bath lengths are 5 feet, 5 ½ feet, and 6 feet.
The second most important dimension is the width of the bath. Available widths are: 30", 32", 36", 42", 48", 54" and 60".
The standard height of a Jason bath is 20 ½". Baths with heights up to 25" are also available.
back to top
Q: How do I select a 2-person bath?
A: Unless the width of the bath selected is at least 48", the drain location usually determines whether the bath can be used as a one-person or two-person bath. The drain located toward the center of the bath allows seating at opposing ends. A minimum width of 36" is recommended for a two-person bath with a center drain.
back to top
Q: What shapes should I consider when selecting Jason baths?
A: The most common bath shape is an external rectangle which can be installed in both an alcove or drop-in installation. Jason also offers many other attractive shapes such as ovals and corner-shaped baths. Baths with rounded corners or oval shapes are not usually installed in an alcove because they do not fit flush against the walls. For corner installations corner shaped baths or oval baths installed cross-wise in the corner angle can be selected. For special design effect Jason offers a variety of round, free-form, and pedestal baths. For all undermount installations, baths with flat decks must be selected.
back to top
Q: What colors are available?
A: Jason baths are offered in three standard colors of White, Natural Bone, and Bisquite. Seven additional colors of Sand, Quicksilver, Sandbar, Almond Bone, Black, Glacier Gray, and Linen are also available for an additional charge. The IC635P translucent pedestal bath is available in Arctic Blue, Glacier Green, and Frost.
back to top
INSTALLING A JASON PRODUCT
Q: What is the electrical supply service needed for a Jason therapy bath?
A: The electrical supply needed will depend on the bath you purchase. Most will require a 60 cycle power supply with one or more dedicated 120V or 240V Ground Fault Circuit Interrupter (GFCI) protected 15, 20 or 30 Amp circuit(s) in accordance with the National Electric Code. Please check the individual bath
specification sheet for exact information.
back to top
Q: What type of service access is required for my Jason therapy bath?
A: The minimum access requirement is 30” x 17” for smaller baths, but most baths require a 36” x 17” access panel, please see the specifications table in your owner's installation manual for bath specific requirements. For combination baths, there should be access to both the blower and pump. The Service Warranty will be void if proper access is not provided.
back to top
Q: What size water heater is needed for operating my Jason therapy bath?
A: The water heater size requirements are determined by the amount of water used in bathing (operating capacity) which is approximately 2/3 of the total internal capacity of the bath but could be greater depending on the number of water outlets connected to the water heater. Specific bath operating capacities are located in the bath Specification Sheets.
back to top
Q: What is a Level-Form™ Base?
A: The Level-Form™ Base is a specially formulated and patented foam infrastructure incorporated into every Jason bath. It is essential to provide rigid support and heat insulation, to dampen sound and vibration, and
eliminates costly grout work during installation.
back to top
Q: Does Jason offer installation templates?
A: Jason produces installation templates for all oval baths. Templates are not offered with any other shape. Each oval bath contains the template with its documentation when shipped. When ordered beforehand, a $20 processing and shipping fee applies.
back to top
CLEANING AND CARE OF YOUR JASON BATH
Q: How should I maintain the acrylic surface of my whirlpool bath?
A: Jason uses the best quality Lucite® acrylic available on the market today. Acrylic surface is very easy to clean and maintain and we suggest Jason Bath System Cleaner be used to clean and maintain the bath. Novus No.1 Acrylic Cleaner gently cleans your bath without scratching and Novus No.2 Acrylic Polish removes fine scratches, haziness, and abrasions from most plastics. All of these products can be ordered through any
authorized Jason Showroom.
back to top
Q: How should I clean the plumbing lines of my whirlpool bath?
A: Jason manufactures the most hygienic bath on the market. Our V-Drain™ Jet System is engineered to ensure maximum water drainage from the plumbing system after each use. You can also purchase an Automatic Ozone Sanitation System that works automatically to quickly destroy bacteria, viruses, and fungi.
To assist in maintaining the plumbing of the bathtub, Jason has developed its Jason Bath System Cleaner, a specially formulated, non-toxic cleaner which can operate safely in all whirlpool and airbaths. Do not use the bath during cleaning process.
back to top
Q: Can I add oils and bathing salts to my Jason therapy bath?
A: Aromatic salts and herbal extracts added to the water can contribute a sensational dimension to your bathing experience. Jason designs its products to safely accommodate many aromatherapy products. We do not recommend using oils in your bath, as they leave the bath surface slippery and contaminate the air jet system.
back to top
PURCHASING JASON PRODUCTS
Q: Where can I purchase Jason products?
A: Jason products are sold through specialized bath showrooms, plumbing wholesalers, and other professional plumbing outlets nationwide. For the location of the authorized Jason showroom nearest you, click on "
Find a Showroom.”
back to top
Q: How can I obtain pricing information and purchase Jason products?
A: Jason products may be purchased through a nationwide network of specialized bath showrooms, plumbing wholesalers, and other professional plumbing outlets. Any one of these authorized distributors can provide you with pricing information and ordering considerations. To find a Jason distributor in your area, please click on “
Find a Showroom,” or contact our Customer Service Department at 800-255-5766.
back to top
Q: What is the usual lead time for Jason baths, and can I quick ship a bath?
A: Since all Jason baths are custom crafted, the usual lead time for production is ten business days. If you are interested in a white bath, it may be possible to shorten the fabrication window to three days. For a more accurate timeframe, please have your authorized Jason Distributor consult our Customer Service Department.
back to top
Q: Can I buy Jason products directly?
A: Jason products are sold throughout specialized bath showrooms, plumbing wholesalers, and other professional plumbing outlets nationwide. For the location of the authorized Jason Distributor nearest you, click on “
Find a Showroom.”
back to top
Q: How do I register my bath?
A: Click on
Warranty Registration under the “Support” tab of this website.
back to top
Q: Where can I locate the serial number for my bath?
A: The serial number can be located in one of these places: just above the motor on Whirlpool baths; just above the blower on AirMasseur® baths; on the front page of the Owner’s Manual; or on the original invoice. The serial number starts with an S and is followed by a series of 5-7 numbers. All Jason baths are tracked by the serial number allowing for more effective communication and service.
back to top